padl router d-link dsl-504

[m19wawa]

mam problem zapomnialem hasla .... i takie tam do router
skasowalem firmware i teraz nie moge wgrac nowego
w terminalu wyswietla mi sie cos takiego (troche tam grzebalem jako laik)
firmware upgrade utility nie dziala!!
192.168.0.1>

]
]
]
]help
Commands to the console are:
configeeprom display EEPROM configuration information
configflash display FLASH configuration information
copyimages {yes | no} copy network booted image files
flashfs {auto | emergency} use automatic FLASHFS selecti
force boot from emergency FLASHFS
initialise initialise configuration information
listenv list environment variables
mac <address> set MAC address
serialboot yes boot from EEPROM
serialboot no boot from FLASH
setenv <key> <value> set environment variable
unsetenv <key> unset environment variable
The following boot modes are supported by serial EEPROM v3.0+ only:
serialboot {yes | auto} boot via EEPROM, auto-select Ethernet or USB

serialboot ethernet boot via EEPROM from Ethernet only
serialboot usb boot via EEPROM from USB only
serialboot no boot from FLASH
dw <address> [<length>] dump words (hex/ascii)
enter <address> enter an image
erw <wrdaddress> read a single word from EEPROM
eww <wrdaddress> <value> write a single word to EEPROM
fdw <address> [<length>] dump flash words (hex/ascii)
flash config print flash configuration
help print this text
quit leave the console
reset reset system
rw <address> read a single word
tftp download image using tftp
why reason for console entry
ww <address> <value> write a single word
xmodem [fast] download
]reset NBfs1Z
PP Boot 8.2.0.16 (25 June 2002)
Copyright (c) 2002 D-Link Corp.
SDRAM size = 0x1000000
'NPimage' not found
Flash boot failed.

Entered console ... No, or bad, ATMOS images.
]ip
??
]
help
Commands to the console are:
configeeprom display EEPROM configuration information
configflash display FLASH configuration information
copyimages {yes | no} copy network booted image files
flashfs {auto | emergency} use automatic FLASHFS selection or
force boot from emergency FLASHFS
initialise initialise configuration information
listenv list environment variables
mac <address> set MAC address
serialboot yes boot from EEPROM
serialboot no boot from FLASH
setenv <key> <value> set environment variable
unsetenv <key> unset environment variable
The following boot modes are supported by serial EEPROM v3.0+ only:
serialboot {yes | auto} boot via EEPROM, auto-select Ethernet or USB

serialboot ethernet boot via EEPROM from Ethernet only
serialboot usb boot via EEPROM from USB only
serialboot no boot from FLASH
dw <address> [<length>] dump words (hex/ascii)
enter <address> enter an image
erw <wrdaddress> read a single word from EEPROM
eww <wrdaddress> <value> write a single word to EEPROM
fdw <address> [<length>] dump flash words (hex/ascii)
flash config print flash configuration
help print this text
quit leave the console
reset reset system
rw <address> read a single word
tftp download image using tftp
why reason for console entry
ww <address> <value> write a single word
xmodem [fast] download
]reset NBfs1Z
PP Boot 8.2.0.16 (25 June 2002)
Copyright (c) 2002 D-Link Corp.
SDRAM size = 0x1000000
'NPimage' not found
Flash boot failed.

Entered console ... No, or bad, ATMOS images.
]info
??
]
configeeprom
No or invalid configuration information
]initialise
??
]flash config
Flash configuration: 2 chips
Chip 0 size 1048576 @ 0xc4000000
Chip 0 ID is 15b: (AMD 29LV800BB 1024k bytes), unlocked (0)
Chip 1 size 1048576 @ 0xc4100000
Chip 1 ID is 15b: (AMD 29LV800BB 1024k bytes), unlocked (0)
Flash start offset: 0x000200
Space for all FLASHFS partitions: 0x001e0000
]erw <wrdaddress>
usage is 'erw <address>'
]erw <192.168.0.1>
usage is 'erw <address>'
]erw 192.168.0.1
usage is 'erw <address>'
]'NPimage' not found
??
]Flash boot failed.
??
]
]Entered console ... No, or bad, ATMOS images.
dodam ze jest to d-link dsl-504 2 generacja
bardzo prosze o pomoc i jesli ktos moze powiedziec krok po kroku jak to zrobic to byl bym bardzo wdzieczny