[andy]

A ja poważnie odpowiadam.

Skoro masz padnięty dysk, to dlaczego w ogóle się zastanawiasz? Nawet jeśli jakimś cudem go zreanimujesz, to tylko szaleniec powierzyłby mu jakiekolwiek wartościowe dane.

Wiesz, że słowa mogą ranić?

Andy kieszen sama w sobie sie przedstawia kontrolerem i jakimis niedobitkami dysku , zobatrz jak sie przedstawia punkt montowania /sdc nie numerem seryjnym dysku tylko jako 0AS i raczej nic nie wymyslisz bez stacjonarnego PC , co ci po logu jak go tam nie ma

Skoro tak to dlaczego na malinie bez problemu mi zwraca status dysku? (tam jest podpięty jak coś inny dysk )

neo@syon ~ $ sudo smartctl --smart=on --all /dev/sda
smartctl 5.41 2011-06-09 r3365 [armv6l-linux-3.6.11+] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green
Device Model: WDC WD7500AADS-00M2B0
Serial Number: WD-WCAV55271866
LU WWN Device Id: 5 0014ee 203bfe6e7
Firmware Version: 01.00A01
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Dec 29 22:18:29 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 174) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3037) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 60
3 Spin_Up_Time 0x0027 114 104 021 Pre-fail Always - 7266
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1030
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 062 062 000 Old_age Always - 27783
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1012
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 612
193 Load_Cycle_Count 0x0032 159 159 000 Old_age Always - 124827
194 Temperature_Celsius 0x0022 109 097 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

SMART Error Log Version: 1
Warning: ATA error count 192 inconsistent with error log pointer 3

ATA Error Count: 192 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Nie mam nic do tego, że proponujesz podpięcie pod kompa przez SATA. Tak samo pomyślałem zanim to napisałem. Niestety obecnie nie dysponuje takim komputerem, więc potrzebuje alternatywnej metody